2 Ports Card E/-E Controller Express To 3.0 6Gb Expansion Adapter L 88SE9125 Ch With Cable

2 Ports Card E/-E Controller Expre to 3.0 6Gb Expansion Adapter l 88SE9125 Ch with Cable

About Descrtion:

!

Feature: 1. Compliant with Serial ATA Specification 3.0, down compatible with 2.0 1.0. 2. Conformance to -Expre v2.0 specifications, down compatible with -Expre v1.0. 3. Supports communication speeds of 6.0Gbps,3.0Gbps and 1.5Gbps. 4. Supports Gen 1i,Gen 2i,Gen 2m, Gen 2x and Gen 3i. 5. Supports two Ports. 6. Supports AHCI 1.0 and IDE modes. 7. Supports Native Command Queuing(NCQ) 8. Supports Port Multlier FIS based switching or command based switching. 9. Supports Hot Plug and Hot Swap. 10. Compatible with 6G,3G and 1.5G Hard Drives Specification: Product interface: -E 1X 4X 8X 16X Chest: 9125 Support specification: 3.0 7PIN Bus interface: -Expre X1 slot Extension interface: 2 3.0 interfaces System requirements: there is an available Expre X1 slot, while supporting -E X2 X4 X8 X16 Operating system: Windows10/8/7 (32/64 bit) / Vista (32/64 bit) / XP/2003/2008/linux Note:

1. Please use 3.0 data line to achieve the best results

2. -E slot must have a V2.0 or higher slot, V1.0 will not exceed 250M, -E is X1 or X16 as long as it is V2.0 version, there is spare X16 slot directly inserted On the X16 slot, 3. BOIS setting of the : mode should be changed to AHCI, although some E is version 2.0, but BOIS does not enable high-speed transmiion mode by default (gen2 high speed mode) needs to be manually turned on under -E 1.0 only 200- 250M, 2.0 below 350-400M If you do not accept, please change the . Note: Product driver files: 1. CD-ROM: ... DRIVER \ CARD \ l \ 9125, and then select the appropriate folder according to the system The E to 3.0 adapter card is used as follows: I. Connection conditions and solutions of system disk and E to 3.0 adapter card: 1. The interface mode of E to 3.0 is AHCI mode. If you want to insert a system disk on our card, the premise is that your system disk must be installed in AHCI mode when the system is installed on the , otherwise it cannot pa. Our card transfer card activates the system. 2. If it is determined that the interface installation system of the system disk inserted in the is AHCI mode, you can directly insert the hard disk into our card, and then enter the BIOS to set the system disk to the first boot. 3. Both of the above conditions are met. If it still fails to start or restart repeatedly, it may be that the hard disk interface of the conflicts with our adapter card. The solution is to enter the BIOS and set the hard disk interface option to Disabled, save and restart to start the system Second, the connection conditions and solutions of ordinary disk and E to 3.0: 1. When the system disk is inserted on the and the ordinary disk is inserted on the E to 3.0 card, then only the adapter card information and the ordinary disk model need to be detected at startup. 2. If condition 1 is satisfied and the system cannot be started, then enter the BIOS and set the system disk to the first boot. Third, the system disk and ordinary disk and E to 3.0 connection and solution: 1. Premise, if the system disk with the installed system is AHCI mode test, you can use the following methods to achieve it. If the system is installed in IDE mode, then you can only reinstall the system by E to 3.0. . After the conditions of 2 and 1 are satisfied, you cannot enter the BIOS of the , and set the first system disk as the first boot. 3, 1.2 conditions are met, or can not start, then it may be a conflict of integrated interface, please enter the BIOS and set to Disabled.

You'll receive:

1 x -E to 3.0 Extension Card 2 x Cable 1 x Small and Big Bracket 1 x Screw

Please check tures for more details.

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.