12V 24V Lithium Battery Charging Control Module Protection Board XH-M600 XH-M601 XH-M602 XH-M603 XH-M604 Battery Charger Board-XH-M601 12V A

Ordering instructions: XH-M350 is a battery emergency switching module XH-M600 is an overcharge protection board for battery charging control module XH-M601/XH-M602/XH-M603/XH-M604 is a battery lithium battery charging control module XH-M609 is a battery over-discharge protection module

XH-M601

Product Introduction: 1.Name:12V charger power control board 2.Model:XH-M601 3.Power Supply Voltage:13.8-14.8V 4.Relay Operating Voltage:12.4V 5.Relay Disconnect Voltage:14.8V 6.Voltage Tolerance:+/-0.1V 7.Voltage Detection Way:DC 8.Charging Type:12V storage battery 9.Potentiometer Adjustment:RP1 RP2 10.Size:50*32*18mm Potentiometer Adjustment: 1.RP1:adjust storage battery start charging voltage (low voltage setting:clockwise becomes higher,counter-clockwise becomes lower) 2.RP2:adjust storage battery disconnect charging voltage (low voltage setting:clockwise becomes higher,counter-clockwise becomes lower)

XH-M602

Features: The product name:Numerical control battery charging control module input voltage:AC 220 V Display precision:0.1v Control precision:0.1v output type: output switch Voltage error:+0.1v/-0.1v of application:3.7v~120v all the lithium battery weight:110g size:86*58*24(mm)

XH-M603

Product Introduction: 1.Model:XH-M603 2.Input Voltage:DC 10-30V 3.Display Precision:0.1V 4.Control Precision:0.1V 5.Output Type:direct output 6.Voltage Tolerance:+/-0.1V 7.Application Fields:12-24V storage battery 8.Size;82*58*18mm Using Method: 1.Set Starting Voltage:in normal display voltage state,pre the on will display start charging voltage;long pre for 3s the digital tube will f;you can start or stop on to set starting up charge voltage value 2.Set Stop Voltage:in normal display voltage state,pre the on will display stoping charge voltage;long pre the on for 3s the digital tube will f;you can start or stop on to set stoping charge voltage value 3.Factory Reset:in power on state pre the start/stop on at the same time,digital tube will display 888;that represents factory reset settings

XH-M604

Descrtion Input Voltage:DC 6-60V Display Accuracy:0.1V Control Accuracy:0.1V Output Type:direct output Voltage Tolerance:±0.1V Apply For:6-60V MAX 80V battery Dimension:81*54*18mm Use: In the setting voltage value, start on play on raised, about stop on role to down key 1. Set the start voltage: Normal display voltage state, pre to a starting voltage on ,to display the start charging voltage. long Pre the start on, digital fes, by start and stop on, set the start charging voltage value. 2. Set Stop voltage: Normal Voltage normal display mode, pre to a Stop voltage on ,to display the Stop charging voltage. long Pre the Stop on, digital fes, by start and stop on, set the Stop charging voltage value. 3. Setting Error: Energized state while holding down the start / stop on, digital display 888, which is the factory setting.

XH-M350

This module is for storage battery emergency switch.

It adopts the high quality industrial relay and the effective control current can reach 12A. In control of 12V, power can reach 150W. It is widely used in incubators, computers, networks and so on.

2. Parameters:

No.

Parameter

Value

1

Product name

Storage battery emergency switch module

2

Model

XH-M350

3

Control voltage

DC12V

4

Control current

12A

5

Support power

150W

6

Size

54*26.6mm

XH-M600 Product Introduction: 1.Model:XH-M600 2.control voltage :DC 6-60V 3 control current: max 30A 4 Control Precision:0.1V 5 Output Type:direct output 6 Voltage Tolerance:+/-0.1V 7 Application Fields:6-60V battery 8 Size:84*60mm Using Method: 1:connect to battery(if not,won't have display) 2:pre the "+" display upper limit volatge , long pre will fing ,then set the upper limit volatge (H) 3:pre the "-" display lower limit volatge , long pre will fing ,then set the lower limit volatge (L) 4:connect to the  charger 5： can pre the  set  close the  display save electricity XH-M609

1. Parameters:

No.

Parameter

Value

1

Product name

Battery overdischarge protection module

2

Model

XH - M609

3

Power supply voltage

The 12 V- 36 V battery

4

Output voltage

Equal to power supply voltage

5

Control precision

0.1 V

6

Power consumption

Le than 1.5 W

7

of application

Various storage batteries, lithium batteries

8

Net weight

28 g

9

Size

57 * 42 * 19 mm

2. Features:

1>. Automatic power off.

2>. Discharge protection.

3>. Prolong battery life.

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.