1PCS PWM To Voltage Converter Module 0%-100% To 0-10V For PLC MCU Digital To Og Signal PWM Adjustabl Converter Power Module

PWM to Voltage: Descrtion: 1: Wide range of applications 2: Easy to operate, can be fine-tuned by potentiometer 3: The module is small, easy to carry and easy to use; 4: Adopt single ch embedded technology; 5: Simple and easy to understand Product parameters: 1. Adopt single ch embedded technology; 2. The peak value is 4.5V to 10V level, and the jumper is inserted at 5V. This type of level signal is mainly aimed at the interface of the 5V CPU of the conventional industrial control card (such as H3 board); 3. Easy to operate, can be fine-tuned by potentiometer; 4. Select the PWM signal input level range by short-circuiting; 5. The module is small, easy to carry and easy to use; 6. Module working voltage: DC12V-30V (power requirements: greater than 100MA); 7. PWM signal receiving frequency range: 1KHZ-3KHZ; 8. PWM signal input level range:; 9. Peak 12 to 24V level, the jumper is inserted at 24V. This type of level signal is mainly aimed at the conventional PLC interface; 10. Conversion range: 0%-100% PWM conversion to 0-10V voltage; 11. Allowable error: 5%; Voltage to PWM Descrtion: 1: Wide range of applications 2: Easy to operate, can be fine-tuned by potentiometer 3: The module is small, easy to carry and easy to use; 4: Adopt single ch embedded technology; 5: Simple and easy to understand Product parameters 1. Adopt single ch embedded technology; 2. Easy to operate, can be fine-tuned by potentiometer; 3. Select different input voltage ranges through the short circuit; 4. The module is small, easy to carry and use; 5. Module working voltage: DC5V-12V; 6. Conversion range: 0-5V/0-10V voltage is converted to 0%-100% PWM; 7. Allowable error: 1%-3%; 8. Output PWM amplitude: 5V 9. Output PWM frequency: about 50KHz (1) VCC: Working power supply 5V-12V. (2) GND: working power ground (3) VIN: Input voltage 0-10v. (4) GND: Input voltage ground. (5) GND: output PWM ground. (6) PWM: output PWM. (7) Operation instructions. Connect the working voltage to VCC and GND, not re, so as not to damage the board and device (8) Connect the controllable voltage to the VIN terminal, the voltage range is divided into 0-5V and 0-10v according to the selected mode. (9) The output at the PWM terminal is PWM. (10) The duty cycle can be adjusted by adjusting the voltage. (11) The accuracy can be controlled by adjusting the potentiometer.

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.