200AH 250V Smart Automatic Repair 12/24V Car Battery Charger 5 Stage ligent Charging For Car SUV TruMotorcycle

Car Battery Charger

1.Applicable to the 12V/24V lead acid battery. 2.Advanced width modulation (PWM) technology. 3.Five Charging Modes: No-load Mode/Constant Current Mode/Constant Voltage Mode/Float Mode/Trickle Mode. 4.The battery life can be significantly improved by dial repairing method for the power chips of microcomputers. Package Included: 1 X Car Battery Charger 1 X User Manual For 12V/24V, 6-200AH Lead Acid Battery or Lithium Battery of motorcycles, van, sport utility vehicle etc.

For 12V/24V,6-200AH Lead Acid Battery or Lithium Battery of motorcycles,van sport utility vehicle etc.

Car Battery Charger

power:220W

Output voltage: 12/24V

Input Voltage:130V-250V

Gro weight:800g

Output current:12V-12A 2V-10A

Capatity:30-200AH

dimension:180*145*70mm

Application: best suitable for 12,24v,lead acid batteries(including wet and dry)

This item can be used both 110V/220V of input AC power.

LED

Introduction

5-Stage Mode

24V

Light On

For 24V Battery

12V

Light On

For12V Battery

Mode

Pre

12/24V Battery

No-load Mode

when there has no load connected with charger,the LED Screen will show voltage only,the power is about 2W;

Constant Current

means the battery voltage is lower than the set voltage of charger,then the charger supply constantcharging current to maintenance both battery and battery charger;

Constant Voltage

advanced width modulation (PWM) technology,control the charger's current and output voltageaccurate,avoid overcharge;

Floating charge

when the battery is going to be charged full,the charger will stop charging,but still supplyconstant floating voltage and small current to battery;

Trickle charge

when the battery voltage and current is approaching the set voltage and current,it will turn totrickle floating charge from automatic mode,it means charge full,also can be charged with floating mode.

VI. Charging operation

Step 1, Examine and e sure rated voltage of battery is conforming to output voltage of charger.

Step 2, Connect correctly the charger and the battery.

Step 3, Examine and e sure mains supply voltage is conforming to input voltage of the charger.

Step 4, Connect mains supply and the battery, watch to see if the indicator is on and the cooling fan is working when charging.

Step 5, if the charger refuse to work, turn off mains supply immediately and cheall the connecting cables between mains supply, the battery and the charger.

After only a few minutes or even shorter time, the battery indicates fully charged.

1. Examine to see if there is overcurrent protection, overheat protection or low voltage protection resulted out of non-conforming voltage, and also examine if cooling fan is working.

2. Maybe the battery is consumed up or already fully charged (better test again after discharging or take other battery for testing purpose).

3. Add battery tune-up treatment or distilled water.

4. Examine and e sure output clips from charger is well connected to battery poles.

Battery shell is heating when charging or the battery can't be fully charged after a time's charging.

1. Cheto see if there is short circuit in battery, which shall result in fai of charging voltage reaching the charger's preset voltage.

2. There is a leakage 0.3A≥ in battery.

3. Defective materials or workmanship is used in battery production. batteries are strongly recommended.

4. Rep battery and test again.

The charger beeps for alarming or re to work though all cables are correctly connected.

1. Examine the battery to see if there is low voltage protection due to badly power insufficiency (non-conforming voltage).

2. Termination of service life due to long-time stalledne or short circuit due to large internal resistance.

3. Cheto see if the battery still beeps for alarming when connected only to mains supply unloaded.

4. Rep battery and test again.

For vehicle batteries, motorcycle batteries (small volume) which have been l unused for a time, the charging indicator may not go ON when charging (due to small current requirement resulted out of large internal resistance).In this situation, you can charge at the same time of huge power discharging (consumption).By this means you can judge if the charger is defective, and at the time the charging indicator will f.(Normally, you can continue to floating charge for approximately 1 hour after the charging indicator turns Off until the fully charged. At this time, the battery is in excellent condition, you can use freely) (Though the indicator does not f, the charger is in fact charging the battery in trickle floating mode. And, once large current need from the battery is detected by the charger, the indicator wilo fing).

SPECIAL NOTICE:

1. Charging batteries of leakage for the first time shall be under manual monitoring. To avoid overcharging and bubbling, for the 1st and 2nd time, charging shall be stopped immediately once temperature rise is found of the battery. Temperature rise indicates that the battery is full before g charged or there is leakage which does not influence its usage.

2. When the charger is charging the battery, the cooling fan shall be working regularly.

3. An adjustable charger can adjust current size in acconce with battery needs for a better battery protection. For example, if the current is 30A before charging, you are ased to decrease to 25A. Similarly, if 25A, you are ased to decrease to 20A. The 20% spacing shall better protect your battery as well as your charger.

If the battery is not needed urgently, you are ased to charge by 1/10, i.e. 10AH battery to 1A charging current.