3.3-5V 0.36 Inch 5 Digit LED Meter Brushless Motor Special Tachometer Speed R Digital Frequency Meter Digital Meter

Product selling point

1: Adopt industrial-grade high-speed MCU, strong anti-interference

2: Stable and reliable

3: Features of wide measurement range and high measurement accuracy

4: Small appearance

5: Widely used

Newly developed, tailor-made three-phase DC brushle drive products supporting tachometer, using industrial-grade high-speed MCU, strong anti-interference, stable and reliable, wide measurement range and high measurement accuracy, the adopts the leading fully synchronous cycle measurement method, the measurement range And the measurement accuracy is a more qualitative leap, applicable to all three-phase DC brushle drive boards and drive modules with rotational speed signal output on the market, and the three-phase brushle drive products independently developed by our store have reserved interfaces for plug-and-play.

Two setting ons on the back and interface line definition

Note that this product has re connection protection. The default power supply voltage is DC 3.3-5V, and the measured signal amplitude is 3-30V. If this parameter is exceeded, it may be permanently damaged.

2. Product features

1. High frequency measurement accuracy, up to 0.01‰ at 25 degrees Celsius, and resolution up to 0.001HZ.

2. The frequency measurement range is wide, 0.15HZ-100KHZ. It can also be customized for ultra-low frequency measurement 0.01HZ-100HZ3. The range is automatically switched from 00.000Hz (R/M to 000.00KHz (KR/M).

4. The working mode can be switched by preing the on, including two working modes of frequency and speed, and the working mode is saved when power off.

5. The frequency division value can be set by preing the key. The frequency division value can be 1-99999 and 0.0001-9.9999. The frequency division value is saved after power-off.

6. Beautiful appearance, sophisticated craftsmansh and easy to use.

Display digits: 5-digit LED digital tube (0.36’).

Display refresh rate: signal frequency> 3HZ: 3 times/sec: signal frequency ≤ 3HZ: approximately equal to the signal frequency. .

Overflow display: "-----"

Measurement accuracy: 0.1%±1digit or 0.01‰ at 25℃.

Measuring range: 0.15HZ—100KHZ. 9r-999.99Kr/m

Input signal: Type: dry contact, PNP, NPN, pulse Amplitude: 3-30V

Measurement method: fully synchronized period measurement method.

Input resistance: 100KΩ/resistive.

Power supply: default DC3.3-5V, other voltages are needed, large quantities can be customized

Withstand voltage: AC2000V 1min between the external terminal and the shell.

Use environment (temperature and humidity): temperature-10℃-＋70℃ relative humidity 25-85% (no condensation),

Storage temperature: -20℃-+80℃ (no condensation)

Dimensions (mm): 48*29*18.5 length X width X height)·

Opening size (mm): 45*26

Four, use method

1. There are three wires on the meter head, the red is the 3.3-5V positive power supply, the black is the ground wire, and the yellow is the signal pulse input wire, which are connected to the equment under test respectively.

2. Switch between speed measurement and frequency measurement mode

There are two ons "M mode" and "S selection" on the back. When the power is on, pre the M key once to enter the mode selection interface, and then select 0 frequency plus filter wave test by continuously short preing the S key, and select 1 speed plus filter wave test. Choose 2 frequency without filter wave test, choose 3 speed without filter wave test, wait 4 seconds without operation, automatically save and return to the just set mode and wait for the measurement state.

2. Frequency division value setting

In the power-on state, first pre the S key once to enter the frequency division setting interface. At this time, the S key is the shift function of the 5-digit 8-character on the display screen, and the M key is the value increase. Use the S key to select the 8-character to change the value, and then pre M Key to change the value, the frequency division value must be within 1-99999 or within 0.0001-9.9999, other values are invalid (short pre the S key to move to the rightmost decimal point when it lights up, then short pre the M key to open or close the leftmost decimal point , Realize the decimal point setting) After setting the frequency division value, wait for 7 seconds without operation and automatically save and return to the just set frequency division value and wait for the measurement state.

Explanation of the concept of frequency division value: the number of pulse signals taken when the turntable or gear rotates one revolution during speed measurement. For example, when an external r is used, the turntable or gear rotates one revolution to take 1 pulse signal, and the frequency division value is set to 1. If the brushle drive of our shop cooperates with speed measurement, if the motor has 2 pole pairs, then the frequency division value is set (2*3=6) 6.

Five, matters needing attention

1. It should be used within the parameters of this instrument and in a normal environment.

2. Set the mode correctly according to actual usage requirements. Set the frequency division value correctly.

3. When connecting a high-voltage signal, please don't touch the chs and parts on the board with your hands.

Checklist

1*meter

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.