DIY Wireless Switch DC 12V 1CH Mini Relay Module and 433MHz RF nsmitter e Control for Garage Curtain Home Appliance

Input Voltage: 12 V, RF working mode: rheterodyne

• Receiver sensitivity: > 97 dbm

• nsmitting distance:> 100 m open space

• De mode: MCU de

• e storage: 20

• Support e type: EV1527 learning code

• Working mode: Momentary, tole, latching time delay 5s ,10s ,15s

• Output terminal: NO , NC , COM

• e control battery: 2 x 3 V CR2016 on batteries

Note: Maximum input power is 250 V

Control Mode:

1. S-LoMode: Press->On; Press again->Off Need 1 switch and 1 e control on.

Press one on for working/ ON. Press the same on again for stopping/ OFF.

2. Inter-LoMode: Press->On; Press other on->Off Need 1 switch and 2 e control ons.

Press one on for working/ ON, press another on for stopping/ OFF.

3. Jog Mode: Press and hold->On; Release->Off Need 1 switch and 1 e control on.

Keep pressing one on for working/ ON. Remove your finger for stopping/ OFF.

BlWhite RX / BlBlaRX

Input Voltage: 12 V, RF working mode: rheterodyne

• Receiver sensitivity: > 97 dbm

• nsmitting distance:> 100 m open space

• De mode: MCU de

• e storage: 20

• Support e type: EV1527 learning code

• Working mode: Momentary, tole, latching time delay 5s ,10s ,15s

• Output terminal: NO , NC , COM

• e control battery: 2 x 3 V CR2016 on batteries

Note: Maximum input power is 250 V

Operating Function Description
1 Code learning operation
Inching learning code: After the controller is connected to the power, briefly press the learning code on the light fes once, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful learning code, and the working mode is inching mode.
S locking code learning: After the controller is connected to the power, briefly press the code learning on twice once the light fes, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful code learning, and the working mode is automatic mode.
Interlocking code learning: After the controller is connected to the power, briefly press the code learning on three times press once to f the light once, and then press and hold one on on the e control for 3 seconds such as key A. The controller indicator light fes and remains on, and then press another on on the e control such as key B. The controller indicator light fes to indicate successful code learning, and the working mode is interlocking mode such as AB interlocking.
Delay for 5 seconds to learn code: After the controller is connected to the power, briefly press the learn code on four times once the light fes, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful code learning, and the working mode is automatic shutdown mode with a delay of 5 seconds.
Delay of 10 seconds for learning code: After the controller is connected to the power, briefly press the learn code on five times once the light fes, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful learning code, and the working mode is automatic shutdown mode with a delay of 10 seconds.
Delay for 15 seconds to learn code: After the controller is connected to the power, briefly press the learn code on six times once the light fes, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful code learning, and the working mode is automatic shutdown mode with a delay of 15 seconds.
Delayed code learning by 20 seconds: After the controller is connected to the power, briefly press the code learning on seven times once the light fes, and then press the e control on for 3 seconds. The controller indicator light fes to indicate successful code learning, and the working mode is automatic shutdown mode with a delay of 20 seconds.
2 Clear code operation
Press and hold the learn code on on the controller for 5 seconds until the indicator light fes, indicating successful code clearing.
3 Clear code operation
Jog mode: After learning the code for a single on on the e control, press the on relay to ene, and release the on relay to disconnect.
S locking mode: After learning the code for a single on on the e control, press the on relay once to ene and then press the on relay again to disconnect.
Interlomode: After learning the codes for the two ons on the e control, press the A key to activate the relay, and press the B key to deactivate the relay.
Delay mode: After learning the code for a single on on the e control, press the on relay to ene, and after the delay, it will automatically disconnect.