CA-888 12-18V LCD Universal Board Module Switch Tube 300V For LCD Display TV Maintenance Power Supply Accesosries

CA-888 12-18V LCD Universal Board Module Switch Tube 300V For LCD Display TV Maintenance Power Supply Accesosries

1. Using high-quality materials, the quality is guaranteed

2. Easy to use, good stability

3. Small and exquisite size

4. Beautiful appearance

5. Wide application

use:

The damage to the power board of the LCD display occupies a large proportion. Among them, power driver chs, high-power power switch tubes, sampling s, etc. are the most common damages. Due to the variety and variety of these components, they often cannot be repaired due to the lack of the same spare parts.

The LCD universal power supply module has the advantages of simple wiring, convenient installation, saving time, and improving the succe rate of maintenance.

Pin Definition:

Pin 1: DRAIN, power control terminal, connected to the D pole of the high-power MOS power tube. Usually the middle foot of the power switch tube

2 feet: GND, module ground wire 300v, connected to the negative pole of the , it can be on the same line. Directly connect the negative pole of the large filter

Pin 3: VCC, module power supply terminal, connected to the positive pole of the after rectification at the feedback winding terminal, continuous power supply, the voltage is between 12-18V.

Pin 4: FB, voltage regulator feedback, connect to pin 4 of the , please confirm that pin 3 of the is connected to the hot ground. If it is not the hot ground, short the to the hot ground, and disconnect the perheral circuit of pin 4.

5 feet: start start foot, connect the positive pole of +300v

Please be sure to take a good look at the specific connection method before modifying it, and do not blindly connect it indiscriminately. If you don't understand it, please check the circuit diagram below several times!

How to use:

1. Remove the power ch (usually 8 pins) on the board, and the switch tube (mos tube)

2. Check the 300v and whether there is any bulge on the appearance of the at the load end. If there is any problem, replace it first.

3. Check whether there is a short circuit at the load end, AD board, high voltage board, etc.

4. Connect the corresponding circuit of the module, and carefully check that there is no wrong connection, if the wrong connection will cause the module to burst

5. Install in the position, pay attention to insulation, do not short-circuit

6. Power on, measure whether the voltage is output, if there is no output, check the reason

Precautions:

1. Before using this module, please check whether there is a short circuit at the cold end. If there is a short circuit, repair it first. If the is bulged, please replace it first. If the high-voltage package circuit is short-circuited, disconnect it first. Before this module is installed, remove it. The power ch and mos tube of the module, at this time, the voltage of the electrode in the middle of the switch tube to the hot ground should have a voltage of about 300v.

2. If the 3-pin of the is not connected to the hot ground, please connect the 3-pin to the hot-ground, and at the same time remove the perheral circuit of the 4-pin, and connect the white wire to the 4-pin position.

troubleshooting:

1. No output: the wiring is wrong, it cannot be wrongly connected or mied, this will only burn the ch, make sure there is no short circuit at the load end, is there any problem with the

2. The control of the part is wrong. The 1st pin of the is not grounded, and the 2nd pin is connected to the vcc part through a .

3. The heat is serious. If the tube is used for le than 10 minutes, except for the cause of the heavy load, check the diode and on the hot-end transformer for damage.

4. The voltage is unstable and jumps: the load is too light or too heavy, the continuous jump of the voltage means that the load is too light, and the hiccup is too heavy. Generally, there may be slight voltage jumps when the load is not connected, mainly due to the different design of the transformer. , you can try to connect the load, or connect a 100 ohm at the 5v end to test

Package list:

Module*1

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.