This website uses cookies
This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
Shipped from abroad
Free return within 7 days for eligible items.Details
shangzhong
90%Seller Score
1 Followers
Shipping speed: Average
Quality Score: Excellent
Customer Rating: Excellent
Features:
Installed on the inside of the rear fenders, and emits microwaves for detection. If the sensor detects an effective kicking motion in the sensing area, it outputs a corresponding level signal according to the signal strength to control the opening of the trunk.
Made of durable material,anti-corrosion and wear resistance.
Connection line: Diode protection, fast transmission speed.
24.125GHZ sensor, accurate sensing, fast.
Double fixing holes, durable and not easy to fall off.
Specification:
Microwave module parameters:
Transmitting frequency: Symbol: fStandard. Minimum: 24GHZ Maximum: 24.250GHZ
Output power: Symbol: Pout Typical value: 12dBM
Start-up time: Symbol: St Min: 0.6 Typical: 0.8 Maximum: 1us
Operating voltage: Symbol: VCC Minimum: 3.1V Typical: 3.3V Maximum: 3.6V
Sensing angle: horizontal direction: 80 degree vertical direction: 32 degree
Operating temperature: Symbol: Top Minimum -40 degree centigrade Maximum: +85 degree centigrade
Absolute limit: Operating voltage: 5.5V Operating temperature: -40/+85 degree centigrade Storage temperature: TSTG -45/+90 degree centigrade
Microwave sensor parameters:
Power supply voltage: DC5-18V Boot time: about 2s
Working current: about 5MA
Microwave working mode: intermittent
Transmission frequency: 24.125±0.125GHZ
Protection level: IP68
Installation steps and precautions (post-installation):
1. First wipe the inside position of the rear fenders to be cleaned, leaving no dirt, dust and Foreign matter such as water, the position of the sensor installed in the middle of the rear is optimal;
2. Align the hole mark on the sticker and use the self-contained screw to drill. Pay attention to the direction of the screw cap.Screw cap outward.
3. When the screw is drilled into the fenders by about 1 cm, the drilling is stopped. On the inside of the fenders, the holes on the left and right sides of the microwave sensor are placed on the screws drilled into the fenders, and the white rubber surface is attached as the sensing surface. The sensing surface must face down to the ground. Pay attention to the position of the screw slowly to prevent the screw from scratching the hand;
4. Press and hold the microwave sensor to continue screwing the screw, so that the screw is fixed to the microwave sensor. After tightening the screw, the white glue should be completely attached to the inside of the fenders. There should be no gaps in the middle to prevent the sand from entering and affect the use effect.
5. If there is a mesh, protrusion and other structures on the inside of the fenders, the white glue on the module should not fit completely with the inside of the fenders. Be sure to grind the mesh, protrusion and other structures or fill the glass glue, otherwise the gaps in the middle Mixing in water and sediment can have a significant impact on the performance of the sensor.
Extension cord connection method:
Red line (positive power supply): 12 volts of normal power;
Black line (negative power supply): grounding;
White line (ACC): Use one end of the test pencil to make a good connection between the end and the measured line. At this time, the original car key switch to the ACC, the test pencil light will be on, the ACC is turned off, and the test light is off.
Green line (key line): Use one end of the test pencil to maintain good contact with the line on the original door button socket. Press the original tailgate button, the test light will light up ,it is the tail door button line.
We confidently assure you'll be satisfied with what you get.However, If there's a chance that you are not satisfied with our goods or something else, please let us know before leaving us a Negative feedback. We will try our best for 100% customer satisfaction. Your 5-Star Positive Feedback is much appreciated to us, and your satisfaction is our greatest motivation to move forward.Welcome to Shop Here! Want more Items? Please come & visit our SHOP.
*Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 5 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer).Your satisfaction is our first priority.
*If you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.
This product has no ratings yet.
Subscribe to our newsletter
and be the first one to know about our amazing deals!