DC20-70V To 2.5-58V 30A 800W High Power DC Step-down Power Supply Module Constant Voltage Constant Current Adjustable Voltage

DC20-70V to 2.5-58V 30A 800W High Power DC Step-down Power Supply Module Constant Voltage Constant Current Adjustable Voltage Module Product selling point: 1. High conversion efficiency 2. High-power device, high-power and high-electricity double iron silicon aluminum magnetic ring 3. Anti-re connection of the input MOS tube (the input is not afr of re connection) The output is adjustable with constant voltage and constant current 4. There is an output overcurrent protection indicator. There is an output indicator. 5. High-power profile aluminum , intelligent temperature control fan for heat diation, high reliability, stable work The main parameters: Input voltage: DC20V-70V Input current: 20A max Output voltage: DC 2.5V-58V Adjustable output current: 30A (MAX) Output power: 800W (MAX) Standby current: ≤70mA (input 24V, output 12V) Output rple: ≤120mV (input 24V, output 12V/20A) Conversion efficiency: 92-96% (different voltage and current efficiency are different) Circuit structure: non-isolated (BUCK) Working temperature: -20~60℃ Instructions for use: 1. The input and output cannot be red, and the positive and negative poles of the output cannot be red or short-circuited. 2. The maximum input peak voltage cannot exceed 78V. Too high may damage the module. Please use it within the voltage range. 3. The output voltage and current are continuously adjustable with constant voltage and constant current, which can be adjusted counterclockwise to increase and clockwise to decrease, and the minimum current is 1A. 4. When the input voltage of this module is lower than 30V and the output is lower than 12V, the output can be short-circuited without dam the module. You can use an to short-circuit the modulated output current (but try to short-circuit at low voltage). 5. When adjusting the output current, you can adjust the current and measure the output current reference point voltage with the mV block of the . Every 2mV is 1A of output current. Adjust the reference point voltage to how much current is needed. 6. The two diodes D9 and D10 can be changed to two LED light-emitting diodes, which can be used as constant voltage and constant current working status indicators (can only be changed on the position of the board, not leaded by wires). 7. When the voltage and current are adjusted by external og signals, the external voltage signal is 0-5V. Pay attention to the positive and negative poles when connecting. Note: When the external signal is powered, a separate power supply is required, and it cannot share the ground wire with the module, otherwise the module may be damaged. 8. When you need to adjust the external og signal, you need to remove two s. When you need to adjust the voltage, remove R38 (the second behind the voltage signal port), and when you need to adjust the current, remove R46 (the second behind the current signal port). ), at this time, the two adjustable voltage and current are respectively changed into the adjustment adjustment of voltage and current. If the adjustment adjustment is not needed, the adjustable can be changed to the corresponding fixed resistance 9. This module is not suitable for loads with motors and large starting currents. 10. The maximum output power of this module is 800w. When the output voltage is below 26V, the maximum output current can reach 30A. When the output voltage is higher than 26V, the output current is reduced accordingly. This data is for reference only, and the actual use environment and conditions shall prevail. 11. The MOS tube anti-re connection and current detection of this module are at the negative terminal (ground wire). When the output requires constant current and current limiting, the negative terminals of the input and output cannot be shared or short-circuited, and must be separated. 12. When using, please add heat diation to the module according to different environments and the size of the load. 13. Descrtion of input and output voltage difference: A: Input 70V, maximum output 58V. B: Input 60V, maximum output 49V. c: Input 50V, maximum output 40V. D: Input 40v, maximum output 32V. E: Input 30V, maximum output 24V. F: Input 20V, maximum output 16V. The main function: 1. High-power solar street lamp driver 2. DIY adjustable constant voltage and constant current power supply 3. Constant current drive for various LED lighting 4. Solar charging power supply 5. Power supply for vehicles and various mobile devices 6. Charge various batteries Precautions 1. When the input and output voltage is higher than 36V, please pay attention to the safety of electricity to prevent electric shock. 2. When working with high current, please tighten the screws of the terminal block. 3. When working, the input and output voltage and current can not exceed the maximum value, so as not to damage the power supply. 4. Pay attention to ventilation and heat diation when working with full load for a long time to extend the service life of the power supply. 5. Pay attention to dust and moisture. Package List: 1 x Step-down power supply module

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.