This website uses cookies
This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
Shipped from abroad
Free return within 7 days for eligible items.Details
Sweet Memories
80%Seller Score
18 Followers
Shipping speed: Good
Quality Score: Excellent
Customer Rating: Average
800W PSU can let RD6018 output 18A, or let RD6018 output 60V, but it cannot let RD6018 full output 60V/18A because it is lower than the max output power of RD6018(1080W)
1000W PSU is 68V 17A output at 220V AC input, it can let RD6018 full output, but it is 68V 14.7A (about 1000W) at 110V AC input, so it cannot let RD6018 full output, please set the power limit to 950W in RD6018 setting.
NOTE for Switching power supply: When get the PSU, please use multimeter to che if the real output voltage is stable and fits the rated voltage, to see if it is damaged on the way, if the output is abnormal, please contact us, do not connect it to RD power supply to avoid more lo
Technical Support If you have any questions about our products, welcome to contact us in these ways,for now we support Tencent QQ group, WeChat group and WhatsApp, here is the contact information. QQ Group:550112838 WeChat:15868147353 WhatsApp:+8615868147353
Note before buying:
1, those 2 choice S800 case and S12D case are only case, not containing any power supply. some picture show installation finished by RD6012 , switch power and case .
2, there are 2 choice, S800 case and S12D case . For S800 case, you can put AC-DC switch power and RD6012 into this case. for S12D, you can only put RD6012.
RD6012/RD6018 and S800 case aemble instruction : https://drive.google.com/drive/folders/1LNymuq8olL32XDJXZFeQow7xtbuP6bMI?usp=sharing
RD6012 /RD6018 and S12D case aemble instruction : https://drive.google.com/drive/folders/1T66hTdQfkDyEG0yMzu-64BNY5Za8CmSn?usp=sharing
Installation video : https://youtu.be/RkIH9xOx_5M
there may be scratches on the surface but it doesn't affect the product performance, please do not be over piy, and if you do mind this, please do not buy this product
3, for S800 case, it is just case, not conntaining any power supply, but it is suitable for RD6012/RD6012W and AC-DC 800w switch power supply, you can buy them seperately to aemble.
5. install the device in the right way
Friendly reminder: ·there may be high-frequency noise when the 800W 65V switch power supply is powered on and there is no load, which can be improved by adding a load as shown in the figure! But for some people, they can still hear the noise, if you mind the noise, please do not buy this power supply, 800W 68V PSU does not need this ·You can only connect the cables with a foundation in electronic and electrical engineering and it must be reliably grounded! ·Due to expre delivery, some power supply warranty labels may be damaged, which does not affect product warranty! ·Due to the different power supply production batches, the internal material details may be different, hereby explain!
5, for S800 case, durning the shping, maybe the case side wiil be a little deformation (just like picture ), you can use your hand to ajust, that's ok, if you do mind this , please stop buying.
6.when intall our 800W PSU into our case, please follow our instruction to aemble, do not remove the shell of the PSU to use. After the shell of the switching power supply is removed, the structural change of the heat diation system will lead to insufficient heat diation,and some components will be overheated and damaged, in this case we don't offer after sell service
S800 Case Instruction:
Digital power supply case (S800) aembly instruction
This case is suitable for RD6012
Date:2020.5.11
Dear users, thank you for purchasing the digital power supply acceory-metal case produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before aembly. Keep it for future reference.
ATTENTION: Since the aembly proce involves voltage that exceeds the human body's safety, non-profeionals should not operate, you must do insulation and protective measures during the aembly proce, and che the wiring several times for safety, please place the product at a place that children and old people cannot get.
Please use the switch power supply we recommend, and if you use other power source, che if the positions of fixing holes are suitable or not.
2.Product Dimension
3.Acceory List
NAME
SPECIFICATION
QUANTITY
PICTURE
Upper Board
S 800 upper board
1
Lower Board
S 800 lower board
1
Connection
Cables
Brown 32cm:1
Brown 10 cm:1 Yellow Green 32cm:1
Blue 32cm:1
Red 17cm: 2
Bla 17cm: 2
Temperature r extension board :1
9
Roer switch
KCD3
1
AC power soet
AC-04
1
Non-sl mats
Φ13*4
4
Screws for fixing mats, extension board andswitch power supply
M3*4 round head
11
Screws for fixing case and AC power soet
M3*6 flat head(white)
10
4.Acceory Picture
A: Lower Board
B: Upper Board
C: Screws for fixing mats, extension board and switch power supply
D: Screws for fixing case
and AC power soet
E: Non-sl mats
F: Roer switch
G: AC power soet
H: Connection Cables
5.AemblyProcedure
5.1 Aembly Preparation● RD60 XX digital power supply*1, S 800 case*1,800W switch power supply*1
● Tools, acceory(DC power supply, 3 pin plug cable, multimeter, screw driver, test pencil...)
● Proper aembly environment
It is recommended using a 800W switch power supply as shown below.
5.2 Aembly step
Note: The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the aembly, please straighten it before aemble it.
①Che the acceories: che if the acceories ofS800are same as acceorieslist or acceory picture.
②Che RD60XX:Adjust input power supply to 12v/1A to power on RD6012, and set 5V/1A output on RD60XX, turn on the output to see if the output is normal.
③Ba board aembly: install the roer switchandAC power soeton the lower board.
④Connect cables to switch power supply: (dangerous,non-profeionals should not operate)
Uselongbrown cable to connect theroerswitch and the live wire (L) of the switch power supply; then useshortbrown cable to connect theroerswitch and the live wire (L) of the AC power soet; Use the blue cable to connect the neutral wire (N) ofAC power soet and the neutral wire (N) of switch power supply; Use a yellow-green two-colorcableto connect the ground wire (E) ofAC power soet and the ground wire (〨) of switch power supply.Use two red cables to connect the IN+ of the green terminal and the positive electrodes (+V), and use two bla cables to connect the (IN-) of the terminals and negative electrodes (COM). Install the temperature r extension board to the ba panel.
If you want to use S800 for RD6024, you need to solder the connector to the cables first, then you connect the RD6024
⑤Aemble the switch power supply:Installthe switch power supply on the lower board
⑥switch power supply test:
Che the wring again and power on the switch power supply, and use test pencil to che the power and insulation status. Then use multimeter to che if the output is normal, then use screw driver to adjust the output of the switch power supply to about 68V.
⑦RD60XX aembly:If you have CR1220 battery, pleaseinstall the battery with the positive side facing up, if you have WiFi module, please install it like what shows in the picture. InstallRD60XX to the front side in the correct way, otherwise it cannot be installed properly, we make flame tight to prevent the RD60XX from shaking, if the case is slightly deformed, you can gently bend the case to make itstraight.
⑧Connect the rest cables:insert the external temperature r cable, insert the green terminal and sort out the cables.
⑨Install the screws of the case
⑩ Install the foot pads.
⑪If you need to use external temperature detect, you can insert the external temperature r cable to be ba end of the case, and do final test.
S12D Case Instruction: Digital power supply case (S12D) aembly instruction
This case is suitable for RD6006/RD6006-W/RD6012/RD6012-W
Date: 2020.5.21
Dear users, thank you for purchasing the digital power supply acceory-metal case produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before aembly. Keep it for future reference.
1.Notes
● Read this instruction carefully before aembly, if you still have question, please contact us.
● This case is made of cold-rolled steel plate and the surface is sprayed. When aembling and using, prevent it from scratching by sharp objects, and avoid direct sunlight and humid environment.
● Avoid short circuit when aembling, connect the electrodes correctly.
● NEVER connect the cables with the power ON.
● Try to avoid vibration and fall.
2.Product Dimension3.Acceory List
NAME
SPECIFICATION
QUANTITY
PICTURE
Upper Board
S12D
1
Lower Board
S12D
1
Cable
RED:2
BLA:1
3
Female Banana Soet
M4*36
2
Roer switch
KCD3
1
Non-sl mat
Φ13*4
4
Mat fixing screw
M3*5*7
4
case fixing screw
M3*6
flat head white
8
4.AcceoryPicture
A: Upper Board
B:Lower Board
C: Non-sl Mat
D: Screws for Non-sl Mat
E: Case Fixing Screw
F: Cable
G: Roer Switch
H: Female Banana Soet
5.AemblyProcedure 5.1 Aembly Preparation● RD series digital power supply*1, S12D case*1
● Tools, acceory (DC power supply, screw driver)
● Proper aembly environment
Note: The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the aembly, please straighten it before aemble it.
5.2 AemblyStep1. Che the acceories:
Che if the acceories of S12D are same as acceory list or acceory picture.
2. Install the female banana soets and switch:
Please put the female banana soets and roer switch on the corresponding position of ba board, the red female banana soet is positive electrode and the bla female banana soet is negative electrode. Screw the fixing screws.
1. Connect cable
Use cables to connect switch and female banana soets, and tighten with nuts, the wiring is completed, you can see the final connection below:
1. Connect the terminals, you can connect the U-shaped plug directly to the green terminal of RD6012/RD6012-W, and you need to cut off one side of U-shaped plug and connect them to the green terminal of RD6006/RD6006-W.
5. Install the RD power supply: install the power supply on the front, and insert the green terminal to the power supply, and then connect the external temperature r.
6. Use 12V/1A DC power source to power on the RD series power supply, che if the connection succeeds (che the wiring before power on)
7. Install the upper board: install the upper board on lower board, and use screws to fix it.
8. There are four Non-sl mats, please use screws to fix them.
About shping
This product has no ratings yet.
Subscribe to our newsletter
and be the first one to know about our amazing deals!