Disassemble 12-24V Japanese Nidec 24H Built-in Drive Encoder Brushless Servo Motor Pwm Speed Regulation

Now selling motors that are disaembled, There are scratches on the outside, If you mind the appearance, Please do not buy, thank you! Disaemble Japanese nidec24H built-in drive brushle motor,

The workmanshis very good, the brushle motor,

NMB double ball bearings,

Built-in drive type brushle motor,

With 100-line dual-channel encoder,

Suitable for high precision feedbacontrol,

The motor supports PWM signal speed regulation and forward and re rotation,

With emergency stop function, this motor has a synchronous pulley,

18 teeth MXL timing belt wheel,

The pulley diameter is 11mm,

Remove the pulley shaft diameter 6mm,

The default delivery belt pulley

This motor supports our multifunctional PWM speed control board,

Can support forward and re switching and steple speed regulation,

The speed control board needs to be purchased separately.

https://www.aliexpre.com/item/4000208155563.html?spm=2114.12010615.8148356.57.421741e1gqPGeN

1 patch cord for each motor,

Voltage test can run from 9V~12V~24V,

No-load current 70mA when 9V power supply, the speed is about 2246 rpm,

When 12V power supply, the no-load current is 80mA and the speed is about 3020 rpm

When 24V power supply, the no-load current is 110mA and the speed is about 6100 rpm.

Motor test operation method: connect the red wire to the positive pole,

The blawire is connected to the negative pole,

The yellow wire start wire is connected to the 1k to the positive pole of the power supply,

No resistance is connected below 12V,

Then connect the white PWM line to the negative pole to run at high speed

The white wire input 20KHZ pulse width signal can adjust the speed,

The green wire is connected to the negative pole to switch between positive and negative

Note that the forward and re switching is best to switch after shutdown to prevent instantaneous surges.

Encoder supply voltage 5V,

If you don’t need the encoder, you can leave it alone. (Note that connecting the encoder 5V power supply will also supply the internal control power of the motor. After connecting the encoder 5V power supply, the yellow wire can be turned without being connected. The yellow wire is connected to the negative pole. The motor stops urgently, and the yellow wire is broken. Turn on the motor to start,),

The specific figure below is marked in detail,

Pay attention to wiring during use,

Wrong connection will burn the driver.

Note: It is strictly forbidden to make a mistake in the positive and negative of the brushle motor.

Must use regulated and surge-free DC power supply,

Such as batteries, DC stabilized power supplies, etc.

The motor weighs about 135 grams.

About shipping
Shipping and PaAll itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedbafor the transaction.