DIY Kit Metal Detector Kit Electronic Kit DC 3V-5V DIY Electronic Part Metal Detector

DIY Kit Metal Detector Kit Electronic Kit DC 3V-5V DIY Electronic Part Metal Detector

Product selling point

1: Simple aembly

2: The appearance is small and exquisite

3: Wide range of uses, game entertainment, security , search of metal products on the body, etc.

4: High sensitivity

5: Parts with acrylic shell and without shell can be selected

Kit parameters:

Power supply voltage: 3-5VDC, the kit is powered by a 3V 2302 battery;(no battery)

Uses: game entertainment, security , search of metal products on the body, including mobile phones, controlled knives, etc.

Describe:

Q1, L1, L2, C2, C3, R1, W form a high-frequency oscillation circuit. Adjusting the potentiometer W can change the gain of the oscillation stage and make the oscillator in a critical oscillation state, that is to say, just start the oscillator. Q2 and Q3 form a detection circuit,

When the circuit oscillates normally, when the oscillating voltage AC voltage exceeds 0.6V, Q2 will be turned on in the negative half cycle to short-circuit C4, resulting in Q3 being turned off; when the detection coil L1 is close to a metal object, an eddy current will be generated in the metal conductor, The energy lo in the oscillation loop is increased, the positive feedback is weakened, the oscillation of the oscillator in a critical state is weakened, and the oscillation cannot even be maintained, so that Q2 is turned off, R2 charges C4, and Q3 is turned on to promote the bee The sounds. According to the presence or absence of sound, it can be determined whether there is a metal object under the detection coil.

According to this princle, this circuit can be effectively converted into a proximity switch for elevator floor control. (Photoelectric switches are not suitable for many occasions, because the light-emitting device and the light-receiving device will be blocked due to the influence of environmental dust.)

Example 1 of the application of the princle of this metal detector: If you want to detect whether there is a car paing by on a certain road, because the car chais is 0.5 meters or more from the road, and the cement will be buried at a depth of 5-10CM, so it is buried on the ground. A coil with a diameter of 1 meter can stably, accurately and reliably detect whether there is a car on it, which is of great practical value in highway traffic statistics and parking lot prohibited area statistics.

Example 2 of the application of this metal detector princle: A r is required on each floor of the elevator controller to detect whether the elevator has reached the stop position. If a mechanical travel switch is used, there will be life and reliability factors; if a photocoupler is used If so, there will be a long-term dust deposition fai; therefore, the only way is to install a metal detector to determine whether the circuit is on or off based on the presence or absence of metal. This will have high practical value in many equment and hines.

DIY parts (board + device) Delivery list:

Component name Quantity

1 board

3V 1

100UF25V electrolytic 1

104 ceramic s 2

222 polyester 2

220K 0.25W 1

2.2K 0.25W 1

100 ohm blue and white potentiometer 1

9018 triode 1

9015 triode 1

9012 triode 1

12D07 toggle switch 1

1 CR2032 battery

2032 battery pole piece 1

Debug method:

The L1 and L2 of this hine use copper conductors on the printed board to form inductances. You do not need to make your own inductances. It is simple and has a very high succe rate! The circuit has just used more than ten components, as long as the installation is correct, it can generally work normally. After installation, connect the power supply, adjust the potentiometer to just not make sound (if it is not close to the metal), use the printed board antenna to approach the metal, and it should make a sound at this time. Turn the potentiometer counterclockwise and try again until it meets the requirements.

See question:

The long beep after power-on is because the front oscillator stage did not . It is poible that the s, transistors and other components are misplaced, or there is an inter-turn short circuit or open circuit in the circuit board coil. Please check carefully with a magnifying gla. In addition, the amplification factor of Q2 is too low to make Q3 turn off and it will be long.

Effect: This simple detector can easily, stably and reliably control and measure metal coins, steel plates, iron plates, aluminum plates, computer CDs, etc. with a distance of about 2.5CM from the coil plane (circuit board).

List:

1*Metal detection parts with shell/without shell, optional

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.