F/ NSK Dental LED E- PANA High Speed Handpiece Turbine 3spray SU B2

AUTOCLAVABLE"TURBINE HANDPIECE
In order to keep the handpiece operating normally , water accumulated in the compressor must be drained out ONCE A DAY . DAILYLUBRICATION IS ABSOLUTELY ESSENTIAL

WORKING AIR
Operate the handpiece at pressures of 25 to 30 psi. Engineered to attain speeds of 300, 000 at 25 psi and 400,000 at 30 psi

ATTENTION
● This product is specialized for stomatology treatment, dont use it in ways
● This product is high speed handpiece, be careful when you use it
● This product is for doctorsEvery time you use it, please check first. If find anything unnormal, stop using immediately, and contact your supplier
● The damaged handpiece will caese very high noise, using it for a long time will influence your auditionTo avoid damaged badly, be careful not to drop or hit it
● Please use a bur of Iso-standard, (1.59-160mm, any bent, damaged, or non-concentric burs will cause cartridgedamaged badlyWhile using a bur, make sure that the bur's rotate speed and size fit the handpiece correctly
● While using a bur, make sure that the bur's rotate speed and size fit the handpiece correctly
● Always securely mount a bur in the chuck, even while it is not in use
● Make sure that the rotation has stoped completely before replacing the cartridge or the bur

REPLACEMENT OF CARTRIDGE
Removing old cartridge
Mount a dummy bur in the chuck, then turn the head cap counter-clockwise and remove the head cap. Push the dummy bur andRemoving old cartridgecartridge is easily removed from the head.

Installing new cartridge
Insert new cartridge into handpiece head, sureof the head, to insure proper fit Mount and screw the head cap with fingers till tight. Further tighten with the head cap wrenchcartridge with the groove inside the front.

NOTE: WHEN REPLACING HEAD CAP. DONT USE THE WRENCH AT FIRST. BECAUSE THE THREADSARE VERY FINE AND CAN BENOTEEASILY STRIPPED

AUTOCLAVE PROCEDURE
Remove bur from handpiece and clean handpiece by scrubbing with a toothbrush and then use guaze towel to dry handpieceAfter every using, autoclave procedure should be taken as followsPlace the handpiece in an autoclaving pouch and make marksLubricate handpieceStarting: 20 minutes at 121C, 15 minutes at 135C

Package Contents:
1x Dental High Speed Hand Tool

Technical Specifications:
: Silver
Material: Stainless steel
Fittment: NSK PANA
Head height: 12.5MM
Single water spray
Head diameter: Φ13.15mm
Speed: 300000-350000r/min
Rated : 210-230Kpa(2.1-2.3Kgf/Cm2)
Angle: 90 degrees
Chuck type: Press type

Features and Benefits:
● Design of arc shaped mobile phone based on human principle.
● Increasing durability greatly
● Low noise
● Sanitation head system
● NSK button change pin chuck.
● High temperature and sterilization that can withstand 135 degrees Celsius.
● It can be cleaned in a thermal disinfector.

Notice:
1. Please allow 1-3mm error due to manual measurement.Pls make sure you do not mind before you bid.
2. The may have different as the difference display,pls understand.









a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a