MOFI-Earmax Pro -EMP-Tube-Headphone Amplifier-DIY KIT & Finished Board

Welcome to the MOFI-Acoustics store. In order to provide better shopping experience, let me clarify these informations to avoid unneceary inconvinience:

1. All products in the store are not included: customs duties, customs clearance fees and tax. Without special requirements, we will declare them according to the price of the product.

2. We hope that you can understand the relevant taxation policies of your local customs. We do not accept your refusal for goods due to customs taxation iues; (in some countries, the platform has the option of pre-collecting tariffs).

3. In order not to affect your receipt of the goods, after purchasing the goods, please pay more attention to information such as emails, platform meages, etc. If there is any information about the unclear addre or the logistics policy changes, we will notify you as soon as poible, and look forward to you reply.

DIY KIT Project

To complete this project, high level knowledge of electronics and rich experience in terms of and testing are required.

Due to time zone and language communication restrictions, we can only provide limited technical support, and you need to solve probl by yours.

We do not provide information other than the product introduction page.

MOFI-EMP-Tube-Headphone Amplifier-DIY KIT Project

Compared with the commonly reproduction of EMP, we improved:1、High Voltage：Two-stage buck regulator filter, Two low-pa filter (with a corner frequency of 1.6Hz&16Hz) prevents power noise from g introduced into the amplifier. Provide purer power supply (close to battery).2、The high-voltage power supply uses MOSFET as pa nsistors, which have a sense of tube sound characteristics but rejecting the rectification and regulation noise.3、high-voltage soft-start feature is included which will take about 5 second to reach the designed voltage protecting the tube from any voltage shock.4、Using parallel AC power supply, the voltage distribution is more accurate, better than the deign which is series voltage regulator.5、all-in-one design, single-point grounding, ground resistance is close to the 0.02 resistance value, low noisedesign.6、 is Small with double-sided smt.7、The triangular tube layout reduces the number of dual- common tubes, further improves the separation and reduces crotalk.8、More cost-effective sound modification plan.

SIZE: 102X152X1.6mm

Power requirements:

volt: AC 6.3V,I≥1.2A Best:6.3VAC@2A

high volt:

AC100~260V,I≥0.04A

best:120VAC@0.1A

Product configuration

DIY kit: Contains the and the components needed on the , but does not include the power nsformer and the electronic tube.Finished board: Based on the well-tested board on the standard version kit, we verified all key points' voltage, and used the signal and oscilloscope for og waveform double verification. We will not use this board for listening test.All finished s are all carefully hand-soldered and fully tests, so the price is higher and le cost performance. Price-sensitive consumers but with have DIY ability are recommended to choose the kit.

Schematic & key point of debuing

comes with component s for easy installation.We only refer the schematic of the amplification part of the circuit. If you need full circuit , please read the component value with the by yours; we do not provide additionally.please keep test point voltage close enough to it, +-20% is also permitted.

DIY KIT Instruction

Since the holes are plated through, you only need to solder the parts from the bottom of the board. Do not or enlarge the holes because that would damage the through-plating.Clean both sides of the blank with paper towel and isopropyl or electronics flux remover, then solder the components to the board, starting with the lowest profile parts. This means the s and zener . Then solder the small s, small nsistors, followed by the larger s.e sure the correct part goes into each position on the circuit board. Measure each with your multimeter to ensure it's the proper value.Pay attention to the polarity of electrolytic s, s, , nsistors as well as the orientation.Clean up the solder flux residue from the board with isopropyl (or electronics flux remover) and a brush.Inspect all solder connections carefully, using a magnifying gla, to e sure there are no solder bridges or cold solder joints. Use a multimeter in s scale to check for short circuits.The K2700 are vulnerable to electrostatic discharge damage when you are handling them, so keep their pins plued into anti-static foam while working with them until you're ready to solder them to the board. Set the s pre-mounted with the K2700 aside for now.

Parts list

Pic

DIY KIT

Pic

Finished board