OPA541 Module Audio Amplifier HiFi AMP 5A Current High Voltage High Current Driveable Coil Motor Sound Amplifiter

Parameters:

Module model: OPA541

Module type: low frequency power amplifier

Input signal form: single-ended

Input voltage range: 2Vpp (MAX); generally within the power supply range

Module input impedance: 1K ohm

Module supply voltage: ± 10V ～ ± 40V

Module supply current: ± 5A; large output current requires large supply current

Module output impedance: low impedance

Output voltage range: 68Vpp (MAX); in the case of positive and negative 40V power supply

Output current: 5A (MAX)

Output power: 50W (MAX)

Module gain: 33 times; the default gain is 33 times, the first level is 11 times, the second level is 3 times, G1 = R1 / R2 + 1, G2 = R7 / R4 + 1

Input offset voltage: 200uV (MAX)

Input offset drift: 2uV / ℃ (MAX)

Input bias current: 125nA (MAX)

Input voltage noise: 35nV√Hz (1KHz)

Module weight: 125g

Module protection: none; no re connection protection, unlimited current protection

The module becomes hot: there is a heat sink, and forced air cooling is required at high current

Module heating factors: the input and output voltage is too large or the module is damaged

Module working temperature: -40 ℃-+ 75 ℃ industrial grade

Module features: positive and negative power LED indication

Application range: small signal amplification, audio signal amplifier, motor drive, servo amplifier, etc.

Module interface type: SMA signal signal input and output, 5.08 blue power card wire holder.

Precautions for using the module:

(1) The power consumption of the module is large, and the power supply needs to have a certain margin. It is recommended to use a power supply with a current drive capacity greater than twice the output current. The module can only be powered by dual power supplies.

(2) In order to avoid unneceary interference, it is recommended to use a linear power supply, the power supply cannot exceed plus or minus 40V.

(3) It is recommended to use the SMA to BNC cable to directly observe the output signal for the output signal. Poor contact or poor quality wires may cause signal attenuation or exceive noise.

(4) The SMA port is not available for power output, and a blue terminal block must be used. The SMA port is for observing the signal and must not overpower.

(5) Due to the large power consumption and heat generation, pay attention to ventilation and heat diation for long-term work, and add fans to strengthen heat diation if neceary.

(6) Since the module has a fixed magnification and no external protection circuit, it is recommended to confirm the output power and amplitude before loading to avoid damage to the module.

input:Vpp=100mV Freq=1.00KHz

Frequently asked questions:

Q: Is the magnification fixed? How to adjust?

A: The default magnification of the module is 33 times. If you need to adjust the magnification, you can only replace the on the board. The is 0805. The calculation formula is given in the parameter details.

Q: Can the module directly drive the coil?

A: The module can drive the coil, but the internal resistance of the coil is required to be greater than 4 ohms. If it is le than 4 ohms, a series power resistance is required, otherwise the module may be damaged.

Q: Can the module amplify square wave or pulse? What is the module bandwidth?

A: The module can amplify low-frequency square waves or pulses. Because it is an audio amplifier, the total bandwidth is not high. Signals within 100K can be amplified. The module is compatible with DC input.

Q: Can the module be enlarged 1: 1? That is, only the current is amplified. ?

A: The module can support 1: 1 amplification. You need to modify the resistance configuration magnification yourself. It is not recommended to directly configure the op amp follow mode, which is easy to self-excitation. It is recommended to change to resistance attenuation first, and then operation amplification; the total gain is 1 Just fine.

Q: Why the input sine wave output is square wave? What is the output current? What is the output power?

A: Generally speaking, the input signal is too large, and the op amp is amplified to the cut-off distortion, which is the square wave, or the supply voltage is not enough. Can reduce the input signal and increase the supply voltage to soe. The output current of the module is determined by the output voltage and the load. I = Uout / R. Similarly, the output power P = U * I is also determined by the output voltage and the load resistance. When high power is input, heat diation grease and air cooling can be added.

Q: Can I use the second level directly instead of the first level?

A: You can use the second stage directly, but you need to remove the ch of the first stage, and then input the signal from OUT1. Otherwise, the first-level ch will affect the signal input.

Ch introduction

Warm prompt: Due to Ali shping rules when using differen logistics methods to purchase products,some shping fee will be charged multle times. Please place order first and contact us to change the price.then we will inform you make the payment.Thank you!! Dear buyer,Cainiao Super Economy Globalis free but it could not be tracked since the parcel left China.( without a valid tracking number) ,please choose Standard category logistics if you want a full tracking info. From 1 July 2021, is required under the new EU e-Commerce VAT rules to collect VAT for orders at EUR 150 or le that are shping from outside of EU to buyers located in EU at check-out. Such VAT collected orders shall be declared for customs with IOSS number, this is to ensure that the goods can then be released for free circulation and delivered to you without being charged with VAT or any additional handling fees at the customs. please follow the link: https://service.aliexpre.com/page/knowledge?pageId=37&category=1000021915&knowledge=1060863305&language=en

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.