Precision 4-20mA 0-10V 0-5V Signal Adjustable Voltage Current Simulator LB02G 0-22mA Sink Source For

Precision Adjustable 4-20mA 0-5V 0-10V Upgraded New Version Released BRT LB02G (Upgraded New Version)

* If you need low cost no battery inside type, pls click : 2/3/4-wire 0-20mA 0-10V Signal BRT LB01GNB

New Features: • Max. Output range: max. -10V to 10V., 2/3/4-wire 0-22mA sink or source signal. Voltage output can be exactly 0.00V •O utput range can be 0-20mA, 4-20mA, 0-22mA, 0-1V, 0-5V, 0-10V, 0-2.5V, 0-3.3V, -5V to 5V, 1-5V, 2-10V, etc. switchable and adjustable. • Display modes can be: actual current/voltage signal value display, 0.0-100.0(%), 0.0-50.0 (Hz), switchable. • User can set 9 x fast signal output points, more convenient to do debugging. • Have battery capacity status indicator, and battery voltage value display function. • Support 24V operating power supply via wiring terminals and 5V from USB port, can be used in indoors or outside industrial site. • 1000mAH 3.7V re-chargeable battery embedded inside, *Automatic stopping recharging battery when battery has been fully charged.. • Output accuracy can be calibrated by user, precision 0.01V, 0.01mA output and LED display output signal value accurately. • Adjusting steps can be fine adjustment or rough adjustment, switchable. • Have short-circuited protection circuits and polarity re connection protection circuits in Brightwin signal . • Refined user-friendly external shell, refined accurate encoders' knob to adjust output signal, more slim size. *Its default output range is 0-10V, 0-20mA, user can adjust it to make it output -10V to -10V, 4-20mA, etc., output ranges. *Output accuracy can be calibrated by user.

Technical Parameters

Referential Application Circuits

* Sampling resistance is only for reference, no needed to add when using our .

Parameters Programming Examples:

>> Modify "F001" Coarse/Fine adjustment mode:

>> "F006" Precision calibration steps explanation: * When doing F006 precision calibration, please do adjust the signal output to 10V or 20mA firstly. Figure 1→2:Pre down and hold Knob for 2 seconds till it displays parameter code: "F001"; Figure 2→3: “+” Clockwise rotation once, Display“- - - -”; Figure 3→4: Input Paword “+ – – +”, Display“- - - -”; Figure 4→5: Pre “OK”, If paword is correct, displays “F002”, Otherwise displays “Err” and Exit; Figure 5→6: Rotate Knob till displays “F006”; Figure 6→7: Pre down the knob “OK” to set the value of “F006”, and then modify the value so that the actual output signal value (measured by high precision ) equals to the value displayed in LED panel (10V/20mA); A high precision needed in that step. Figure 7→ : Pre down knob “OK” to Save. Otherwise parameters will not be save if there are no actions taken for more than 10 seconds. * Its output range and display mode setting methods are the same to that steps above, please contact us to get user manual or technical support. * Battery recharging time required is 3-4 hours. When recharging the battery, the LED screen is on (cannot be off), and it can automatically stop to recharge the battery once it has been fully charged. It provides convenience for user to use or 5V, 1A out AC/DC power adapter to recharge it and use it to do calibration at the same time. Please refer to the User Manual to get more details.

Parameters Code Number Table

Parameters Programming Insructions

1.Pre down and hold on for 2 seconds to enter into parameter setting states, then LED meter displays  "F001" (F001 is Parameter Code Number); 2.Turn the Knob to change the parameter code number (When entering into “F002”, user needs to enter paword "+ - - +" first. ); 3.When displaying parameters code number, Pre down knob "OK" to enter into the corresponding parameter value setting state, then rotate knob to modify the parameters. 4.Pre down the knob "OK" to save parameters setting and exit. LED meter displays next parameters code number ( If haven't enter the paword, the signal will be returned back to normally adjusting mode after setting "F001" value ); 5.Rotate the knob directly till the last parameter code number "Fend" is displayed, then pre down the knob to confirm and save. The parameters setting is completed, and the signal returns back to normally operating status. 6.In parameters setting proce, if no any operation to the for more than 10 seconds, the signal will exit setting status and return back to normally operating status. Portable 0-5V 0-10V 4-20mASignal Package including: 1 Unit x Siganl New Upgraded Version 1 Pcs x High quality 2A USB Cable 1 Set x  Profeional User Manual (Easy to understand). *** If you like low cost the same signal without battery inside type, please choose BRT LB01G (click): Portable 0-5V 0-10V 4-20mA with LED Display Adjustable Out DC Current Voltage Signal High Precision

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.