QIACHIP 433.92Mhz DC 5V 12V 24V 48V 10A 4CH Relay Module Receiver EV1527 Wireless e Control Switch 433Mhz for DC Motor DIY

  Product Application Area 

Products can be used in lighting, garage doors, shutter doors, e control curtains, DC motors, motor . and many more

About this item

• 【Universal Wireless e Control】 From simple main e control to autonomous control such as windows, ennce, garage doors, alarm system, lifting devices, light, rolling door

• 【High sensitivity】433Mhz wireless e control can p through walls, floors and doors at a reliable distance. Maximum signal range is up to 164ft/50m with no obstacle,The receiver is suitable for DC 6V~30V voltage, so both DC12V and DC24V is OK. It is more flexible to use.

• 【Stable and Reliable】With high reception sensitivity > - 105dBm, the 2 e control switches adopt wireless technique, non-directional switch, do not disturb each other. It can be used with the e control to switch between momentary/tole/latched 3 working modes

• 【ligent Learning Mechanism】Learning Code provides high security due to low repetition rate and re-learning mode, which allows you to erase the old code and re-learn a new code when a e is lost.

For Receiver Module :

Model: KR1204B-4
Working Voltage: DC 5V-80V
Product Type: 4- e Control Switch
RF Working Mode: ASK rheterodyne Reception
Modulation Mode:ASK
Working Mode: Momentary/Tole/Latched, etc.
Matching Mode: ligent Learning Code.

Quiescent Current:5mA
RF Frequency: 433MHz
Output Current: ≤10A
Receiving Sensitivity: >104dbm

Wiring instructions:
1, +: Connect to the positive 12V power supply
2. - : Connect to the negative electrode of 12V power supply
3, A: output; normally open end of the relay
4, B: output; relay common;
5, C: output; normally closed relay

Operation Introduction:

About Working Mode:
1. Momentary/Jole: Press and hold->On; Release->Off
Keep pressing one on, the corresponding is working /on; Release your finger is stop/OFF. 4 switchreceiver need 4 on e control nsmitter
2. Tole/S-Lock: Press->On; Press again->Off
Press one on for one time, the corresponding is working/on; Press the same on again to stop/OFF. 4 switchreceiver need 4 on e control nsmitter.
3. Latched/Inter-Lock: Press->on; Press other on->Off
Press one on for one time, the corresponding is working/on; Press another on is stop/OFFAt the same time, another corresponding works. 4 switch receiver need 4 ons e control nsmitter.

The Setting of Working Mode:

1.Momentary Mode: Pressing the learning key on on the receiver board once LED Indicator on receiver board will signaling simultaneously, then press any of the e on, signaling three times by e& x27;s LED indicator means setting Momentary Mode successfully.

2. Tole Mode: Pressing two times the learning key on on the receiver board twiceLED Indicator on receiver board will signaling simultaneously,then press any of the e on , signaling three times by e& x27;s LED means setting Tole Mode successfully.

3.Latched Mode: Pressing the learning key on on the receiver board three times LED Indicator on receiver board will signaling simultaneously, then press first e on, follow on second e on, signaling three times by e& x27;s LED indicator means setting Latching Mode successfully first on stands for on, second on stands for off .

4.2CH Momentary + 2CH Tole: Pressing the learning key on on the receiver board four timesLED Indicator on receiver board will signaling simultaneously,then press any of the e on , signaling three times by e& x27;s LED indicator means setting successfully.

5. 2CH Momentary + 2CH Latched: Pressing the learning key on on the receiver board five timesLED Indicator on receiver board will signaling simultaneously, then press any of the e on, signaling three times by e& x27;s LED indicator means setting successfully .

6. 2CH Tole + 2CH Latched: Pressing the learning key on on the receiver board six timesLED Indicator on receiver board will signaling simultaneously, then press any of the e on, signaling three times by e& x27;s LED indicator means setting successfully.

7. 2CH Latching + 2CH Latched: Pressing the learning key on on the receiver board seven timesLED Indicator on receiver board will signaling simultaneously, then press any of the e on, signaling three times by e& x27;s LED indicator means setting successfully.

8. Deleting Existing e Controls Data: Pressing the learning key on on the receiver board eight times, the LED Indicator on receiver board will f for eight times, it means that the existing e controls are deleted successfully.

*If you don& x27;t understand. Please feel free to send us a message. We

will do our best to serve every customer. Happy shopping*.