SK80 DC DC Buck Boost Converter CC CV 0.6-36V 5A Power Module Adjustable Regulated Power Supply Variable 5V 12V 24V

SK80 DC DC Buck Boost Converter CC CV 0.6-36V 5A Power Module Adjustable Regulated Power Supply Variable 5V 12V 24V Descrtion: Product Highlights: 1. Digitally adjusted voltage and current, convenient and fast, industrial quality, high precision, can be directly used in engineering projects； 2. Using profeional power LCD, the interface is clear, the operation is very simple, and it has a nearly perfect protection mechanism； 3. Hardware protection: input terminal anti-re protection, re connection does not burn; output terminal short circuit protection, short circuit does not burn; output terminal is anti-re, no additional anti-re diode is required when charging the battery； 4. protection: overvoltage protection (OTP), overcurrent protection (OCP), overpower protection (OPP), overtemperature protection (OTP), input undervoltage protection (P)； 5. The default adjustable voltage or constant current value can be set, which can be quickly adjusted in various applications； 6. Voltage and current can be locked to prevent misoperation！ 7. Full of materials, stable performance and wide range of uses。 1. Product parameters: Input voltage: DC6.0V-36V (under-4.7V has undervoltage protection P, it is recommended to use the input voltage higher than 7V, when the input voltage is lower than 7V, the output power will be reduced, the lower the input voltage, the smaller the output power) Output voltage：DC0.6V-36V Output current：0-5.100A Output power: under natural heat diation 80W Voltage accuracy: ±0.5%+1 byte，Resolution：0.01V，Factory calibrated accuracy Current accuracy：±0.5%+3 bytes，Resolution：0.001A，Factory calibrated accuracy Conversion efficiency: about 88% Soft start: Yes Input re connection protection: Yes, re connection does not burn Anti-backflow at the output: Yes, can be directly connected to the battery Output short circuit protection:Yes, the output can be shorted directly Temperature protection (OTP): Yes, 100 ℃ Working frequency：180KHZ After setting to CC, the constant current value is adjusted by default. When driving the LED, the fast dimming can be achieved by rotating the code positioner, which is very convenient! 2. Operation instruction of setting interface: 2.1. Pre and hold the rotary encoder on for 3 seconds to enter the setting interface; 2.2. Adjust the size of the parameter by rotating the coded potentiometer, support fast rotation (fast increase / decrease), short pre the rotary potentiometer on to switch the parameter to be adjusted; 2.3. On the maximum capacity (OAH) / maximum energy (OPH) / maximum operating time (OHP) interface, short pre the "ON / OFF" on to select the corresponding function to turn on or off, if it is turned off, it displays "----" "; 2.4. In the maximum capacity (OAH) / maximum energy (OPH) parameter interface, long pre the "ON / OFF" on to select the capacity range (9.999Ah / 99.99Ah / 999.9Ah / 9999Ah, 9.999Wh / 99.99Wh / 999.9Wh / 9999Wh ); 2.5. After the parameter setting is completed, pre and hold the encoder potentiometer on for 3 seconds to exit the setting interface, and the setting parameters are automatically saved; 3.This product has a lock function: Pre and hold the coding potentiometer on for 5 seconds to lock the set voltage and current to prevent misoperation! After locking, pre and hold the code potentiometer on for 5 seconds to unlock! 4.Applications: 4.1. Used as a common buck-boost power supply with overvoltage / overcurrent / overpower / overtemperature / undervoltage protection； (1) Set the voltage value. (2) Set the constant current value (overcurrent protection value); (For example, the set constant current value is 3.00A, then the maximum current when you use the product can only reach 3A, and the LCD will display "CC" when the current reaches 3A Status, otherwise the LCD displays "CV" status) 4.2. Use as a battery charger Products without the constant current function cannot be used to charge the battery. Due to the large voltage difference between the exhausted battery and the charger, the charging current is too large and the battery is damaged. Current charging, when the charging reaches a certain level, it will automatically switch back to constant voltage charging. (1) Determine the float charge voltage and charge current of the ; (if the lithium battery parameter is 3.7V / 2200mAh, then the float charge voltage is 4.2V, if it is a 12V , the float charge voltage is generally set 14V or so) (2) Under no-load conditions, set the voltage value so that the output voltage reaches the float charge voltage; (if the 3.7V lithium battery is charged, adjust the output voltage to 4.2V) (3) Under no-load conditions, set a constant current value (battery charging current); (4) Connect the battery and charge. 4.3. Use as LED constant current driver (1) Determine the working current and maximum working voltage of the LED you need to drive; (2) Under no-load conditions, set the voltage value and current value so that the output voltage reaches the maximum working voltage and current of the LED; (3) Connect the LED and test the hine. This product can realize the steple dimming of LED by adjusting the constant current value (between 0-working current), without strobe! ! 5. Detailed function: 5.1 Capacity / energy / run time statistics: The statistics are automatically started after the power is turned ON. The value of the last state is displayed after the power is turned OFF. The recording is automatically restarted after the power is turned ON again. On the corresponding interface, long pre the ON / OFF on for 3 seconds The corresponding data is automatically cleared. 5.2 Set maximum capacity / maximum energy / maximum running time 5.2.1. Set the maximum capacity (OAH) / energy (OPH): When the OAH / OPH function is activated, when the statistical capacity / energy is higher than the set maximum capacity / energy, the power will automatically turn off the output and f “OAH” / 'OPH' ; After the alarm is lifted, the capacity / energy statistics are automatically cleared; 5.2.2. Set the maximum discharge time (OHP): When the OHP function is activated, when the power supply running time is greater than the set maximum discharge time, the power supply automatically turns off the output and fes "OHP"; after the OHP alarm is released, the time statistics are automatically cleared; This function can achieve quantitative / timed power supply well. Note: When the OAP / OPH and OHP functions are not turned on, the power supply will automatically record the capacity / energy and running time. After the OAH / OPH and OHP functions are turned on, the power supply automatically turns off the output after reaching the set value; The running time is in countdown mode； 6. Precautions: 6.1. Module input VIN- prohibited and output OUT- short circuit, otherwise the constant current function is invalid。 6.2. Please ensure that the power of the power supply is always greater than the power required by the output load！ 6.3. If the product wants to output at full load, the input power should be 15V ~ 36V, the power is above 100W, the lower the input voltage, the smaller the output power, the limit on the input current: maximum 7A, more than 7A, the product will not be able to run for a long time。 6.4. The module has an input undervoltage protection function. The default is about 4.7V. When it is lower than this value, the output will be automatically disconnected. When the voltage is higher than 4.7V, the output will be automatically restored. When the input current is relatively large, do not ignore the partial voltage on the input wire)

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.