SOH-DL6FS Laser~ Head SOH-DL6 WITH DV34 MECHAMISM (DV34 SOH-DL6FS / DL6C / DL6CH /DL6FG CCM~ DV34-DL6FS Optical K C7AB

New SOH-DL6FS Laser~ Head SOH-DL6 WITH DV34 MECHAMISM (DV34 SOH-DL6FS / DL6C / DL6CH /DL6FG CCM~ DV34-DL6FS Optical k C7AB OOTDTY 100% and high quality 1. ~Laser head installation knowledge 1 How to judge the damage of the ~Laser head: The damage of the ~Laser head generally shows that it does not read the disk or it is very difficult to read the disk. Discs with poorer quality cannot be read at all. When the device can recognize the hine normally, it is usually a shock. The problem of the bald head, when the above situation occurs, you only need to disaemble the hine to check the model of the ~Laser head, and then buy the corresponding model Put the bald head on, and the hine can be restored as new. 2. How to judge the model of the ~Laser head: Generally, there is a model on the label of the ~Laser head or on the base, such as If not, please send us the ture taken by the bald head, and we will have profeional and technical personnel to confirm the model for you. Please Confirm the model of the ~Laser head you need before buying to avoid accidental shooting. 3. How to install the ~Laser head: When installing the ~Laser head on the shelf, do not move the balance bar on the shelf. Being demolished When removing the l~Laser head, you only need to adjust the screws on one side of the balance bar, and do not adjust the other side, so as not to affect the leveling. Otherwise, the ~Laser head may not read the disc. If you can’t install it yourself, you can ask a profeional to test the installation after purchase. Install, so as not to cause damage to the ~Laser head and the hine. 4How to open the solder joints When the ~Laser head is shped from the factory, in order to prevent static electricity from dam the ~Lasertube, there are generally protective solder joints. (There is a larger solder joint on the bald circuit board or on the ible cable) Short circuit the power supply pin of the ~Laser tube to the ground, Before installing the bald head, it needs to be soldered with an anti-static iron, and the electric iron is heated to about 250 degrees Celsius-280 degrees Celsius Disconnect the power supply, and then open the protection point, otherwise the ~Laser head will be unusable. Specifications: Use: Computer Model number: SOH-DL6FS Wirele communication: Wire Control note: Please allow 0-1cm error due to manual measurement. Make sure you do not mind before you bid. Due to the difference between different monitors, the ture may not reflect the actual color of the item. Thank you! Package Includes: 1Pcs

About shping
Shping and Pack All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.