TA 50-150W Dual Channel DIY Kits / Finished ClT Class-T Architecture T Audiophile Sound Quality Power Amplifier Board-Kit With IC TA2022

Optional kit or finished board:

(The kit needs to be welded and tested by yourself; TA2022 has been installed on the finished board, and the welding and testing have been completed.)

Use the TA2022 IC:

Optional radiator:

FEATURES :

● Cla-T architecture Cla T amplifier. ● High Power Large power output. 100W @ 4R, 1.0% THD+N 90W @ 4R, 0.1% THD+N 60W @ 8R, 0.1% THD+N ● Audiophile Sound Quality Excellent sound quality 0.015% THD+N @ 70W 4R 0.015% THD+N @ 45W 8R 0.10% IHF-IM @ 25W 4R ● High Efficiency 92% @ 88W 8R 87% @ 125W 4R ● Dynamic Range = 102 dB Dynamic Range = 102 dB ● Mute Input integrated mute function ● Integrated Gate Drive Supply provides integrated gate drive ● Over-current protection integrated over-current protection ● Single ended outputs Outputs can be operated in bridged mode to provide single-ended output and can be set asL bridged output ● The recommended working voltage is AC double 18V to AC double 24V. ● Recommended voltage AC dual 22V ● PCB size: 121×64mm ● Dual channel 100W 4R, can be bridged to 200W 8R mono output. Comes with bridging.

Equipped with filter capacitors from Japan. Two 35V4700UF. 25A high current rectifier bridge. Equipped with special inductors for Japanese digital power amplifiers, fully shielded OFC leads.

relay protection circuit. It adopts Japan Panasonic M coupling input capacitor MKP 3.3UF.

Refer to the picture, the radiator is installed, for reference only:

Wiring diagram, reference:

● Wiring diagram, you can click to save as a clear large diagram. ● After installation, please set the jumper to the non-silent mode. The relay will be closed. ● Adjust the adjustable resistance so that the midpoint voltage (DC voltage between OUT and GND) of the two channels is le than 10MV. ● If it is set to bridge mode, the midpoint voltage needs to be re-adjusted.

Performance test chart:

Actual measurement: Carrier working state, before output filter.

Output after the filter:

Work test:

Half-bridge dual-channel mode Input signal 500MV Output 10V *2

L full bridge mode Input signal 500MV Output signal 20V *1 (Warning: The dual trace probes of the oscilloscope share the same ground, so in the test full bridge mode, the oscilloscope cannot measure the input and output signals at the same time)

Distortion power diagram, for reference:

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.