Vdiagtool V200 12V/24V Automotive Circuit Power Circuit Probe Kit Electrical System Tool 20FT Extension Cable

V200 Electrical System Circuit Features:Better Than P0, PB100????4 Testing Mode:DC voltage, AC voltage, Resistance Test, Test????More Useful Electrical Diagnose Function:Voltage & Polarity Testing, Continuity Testing, Signal Circuit Testing, Activating Components in Your Hand, Activating Components in The Vehicle, Testing iler Lights and Connections, Activating Components W/Ground, Following & Locating Short Circuits, Checking for Bad Ground Contacts.????QuiS-Test:Before you test a circuit or component, be sure your tool is in good order by doing a quis-test.????Current Overload Protection:V200 circuit is short-circuit protected. The internal circuit breaker will trip if it becomes overload.????Build-in Light:Enable you work safer in the dark.????20FT Extension Cable:Covering from the front to the rear of the vehicle, you can easily inspect the entire electrical circuit system.????DC voltage range:0-65V; Resistance range: 0-100 kΩ; Rated current: 1-10 amps; Frequency response of sound paage: 0Hz to 10Khz.4 Working Modes:✅DC Voltage:While V200 voltage in this mode, contact the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volt.✅AC Voltage:While circuit V200 in this mode, contact the probe tip to a circuit, then the LCD display will read the Max. Voltage, the Min. Voltage and frequency.✅Resistance Test:While Vdiagtool V200 in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead.✅ Test:In this mode, the probe tip contact the positive terminal of the , connect the auxiliary ground lead to the negative terminal of the , the screen will display the forward voltage drop, indicates the forward bias. If switch the probe tip and auxiliary ground lead, the screen will not display the voltage, indicates the re bias.QuiS-TestBefore you test a circuit or component, be sure your tool is in good order by doing a quis-test.How to do S-Test for V200 Circuit ?With the tool connected, perform a quis-test. The power switch is a momentary rocker switch located on the tool's body. Flanking the switch are positive and negative mar.Pre the Power Switch forward to activate the tip with a positive voltage. The Red LED should light up and LCD display will read the battery voltage. A beep tone will sound. Let go of the power switch and the LED will turn off and the tone will cease.Pre the Power Switch backward to activate the tip with a negative voltage. The green LED should light up and the LCD display will read 0.0V (ground). A beep tone  will sound. Let go of the power switch and the LED will turn off and the tone will cease. Your tool is working correctly and is now ready for use.V200 Current frequently-used Functions:- Voltage & Polarity Testing- Continuity Testing- Signal Circuit Testing- Activating Components in Your Hand- Activating Components in The Vehicle- Testing iler Lights and Connections- Activating Components W/Ground- Following & Locating Short Circuits- Checking for Bad Ground Contacts

✨Warm Tips:

1. Always perform automotive testing in a safe environment.

2. Wear eye protection that meets ANSI standards.

3. Keep clothing, hair, hands, tools, test equipment, etc away from all moving or hot enging parts.

4. Operate the vehicle in a well ventilated work Area: Exhaust are ous.

5. Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.

Use extremely caution when working around the ignition , distributor cap, ignition wires and spark plugs. These component create Hazardous voltage when engine is running.

6. Put the nsmiion in PARK (for automatic nsmiion) or NEUL (for manual nsmiion) and e sure the parking brake is ened.

7. Keep a fire extinguisher suitable for oline/electrical fires nearby.

8. Don’t connect or disconnect any test equipment while the ignition is on or the enging is running.9. Keep the tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test tool, when neceary.

10. When the power switch in the tool is depreed, battery current/voltage is conducted directly to the tip which may cause sparks when contactiong ground or certain circuits.Therefore the tool should NOT be used around s such as oline or its s. The spark of an energized tool could ignite these s. Use the same caution as you would when using an arc welder.

Two Charging Mode

VDIAGTOOL V200 Electrical Circuit Powered by vehicle’s battery and arette .Specifications:

Display: TFT color display (160 x 128 dpi)Operating Temperature: 0 to 60°C (32 to 140°F)Storage Temperature: -40 to 70°C (-40 to 185 F°)External Power: 12 or 24V power provided via vehicle batteryLength\Width\Height: 28mm\47mm\178mmWeight:1.2kg

Package list:

1×VDIAGTOOL V200 Electric Circuit 1×Probe Tip1×20ft Extension Cable1×Battery Hookup Clips1×arette Adapter1×User's Manual1×Rued Blow Molded Case